Furnace Installation Littleton CO done right the first time

When your old furnace quits in January, you need Furnace Installation Littleton CO homeowners can count on. We replace gas furnaces across Littleton, from Downtown to Ken Caryl, and we size every system with a real Manual J load calculation instead of a guess. Most jobs are quoted same-day and installed within a week, so you are not waiting in a cold house.

Dependable Heating and Cooling across Littleton, Colorado
  • Gas furnaces
  • High-efficiency
  • Emergency swaps
  • Readings on every visitYou see the numbers before we leave
  • Written scope firstFlat price before any work starts
  • Parts on the truckMost repairs finish in one visit
  • Old equipment hauled awayWe leave the space clean

What Is Included in a Furnace Installation

Every furnace install we do includes the core work that makes the system safe, efficient and code-compliant. Add-ons like duct modifications, new thermostats, humidifiers or air cleaners are quoted separately so you can see exactly what you are paying for.

  • Manual J load calculationWe measure every room, check insulation and window quality, and calculate the exact BTU load your home needs. This is the difference between a furnace that heats evenly and one that short cycles and leaves rooms cold.
  • Permit and inspectionWe pull the mechanical permit through Arapahoe County and meet the inspector on site. You get a signed-off permit in your file, which matters when you sell the house and the buyer's inspector asks about the furnace.
  • New flue and condensateHigh-efficiency furnaces need PVC intake and exhaust piping and a proper condensate drain. We run new lines to code, add a neutralizer where required, and route the condensate so it does not freeze or back up into the furnace.
  • Combustion analyzer commissioningBefore we leave, we test flue gas with a combustion analyzer, verify the temperature rise is within manufacturer spec, and check static pressure. You get the readings in writing so you know the unit is running right, not just running.
  • Warranty registrationWe register your manufacturer warranty the same day so you are covered from day one. Most new furnaces carry a 10-year parts warranty, and we walk you through what is covered and how to file a claim if you ever need to.
  • Old unit haul-awayWe remove the old furnace, cap the gas line safely, and haul the unit away. No rusted hulk sitting in your garage for six months waiting on a dump run you never get around to making.
Furnace Installation & Replacement

Furnace installation for homes

We replace gas furnaces in houses, townhomes and condos across Littleton. Every install starts with a room-by-room load calculation so the new unit fits your home, not a rule of thumb.

  • Failed furnace in winter
  • Aging 80% AFUE unit
  • Cold upstairs bedrooms
  • Furnace and AC together

Furnace work for businesses

We install and replace commercial-grade furnaces and rooftop units for small businesses and property managers. Scheduling is coordinated around your operating hours so tenants and customers are not disrupted.

  • RetailAfter-hours installs to keep the store open
  • OfficesZoned furnaces for multi-suite buildings
  • RestaurantsMake-up air and venting handled to code
  • RentalsFast turnarounds between tenants

Furnace Installation Littleton CO: What the Job Actually Involves

Furnace Installation Littleton CO is the removal of your old heating unit and the code-compliant installation of a new gas furnace, sized and vented for your specific home. We pull the permit, run a Manual J load calculation, check static pressure on your existing ductwork, and set the new unit on a proper pad with a fresh condensate line and flue. You get a combustion analyzer test before we leave, not just a handshake.

Most Littleton homes we walk into are running a furnace that was sized by rule of thumb in the 1990s. That means short cycling, uneven rooms, and gas bills that climb every winter. If you have been searching for furnace replacement near me Littleton and getting vague quotes, we give you a written number based on measurements, not a guess. We also handle furnace and AC replacement Littleton CO projects when both systems are at the end of their life.

We size it, permit it, install it, and test it before we leave.

How Our Furnace Replacement Process Works

Five steps from your first call to a warm house. No mystery, no surprise line items, no waiting around for a callback that never comes.

  1. In-home assessment

    In-home assessment

    We walk your home, measure every room, check window quality and insulation, and photograph the existing furnace, flue and ductwork. This takes 45 to 60 minutes. You get a written Manual J load calculation and a clear recommendation on size, not a sales pitch for the biggest unit on the truck.

  2. Written quote and options

    Written quote and options

    You get a line-item quote within 24 hours. We show you two or three furnace options, from a solid Goodman single-stage to a modulating Carrier or Trane, with the efficiency rating and warranty spelled out. Financing options are available if you would rather spread the cost.

  3. Permit and scheduling

    Permit and scheduling

    We pull the mechanical permit through Arapahoe County and schedule the install. Most jobs land within 5 to 10 business days. If your furnace has already failed, we prioritize you and can usually get a crew out within 48 hours, including weekends.

  4. Installation day

    Installation day

    A two-person crew arrives in the morning and is typically done in 6 to 8 hours. We lay drop cloths, remove the old unit, set the new furnace, run the flue and condensate, wire the thermostat, and seal the plenum. You will hear drilling and see us in and out of the mechanical closet all day.

  5. Commissioning and walkthrough

    Commissioning and walkthrough

    Before we leave we run a combustion analyzer on the flue gas, check static pressure, verify the temperature rise is within the manufacturer spec, and test the thermostat through a full heat cycle. Then we walk you through the filter location, the shutoff valve, and the warranty registration.

Tools and Methods We Use on Every Install

  • Manifold gauge set

    Used to set gas pressure at the valve and verify inlet and manifold pressure match the manufacturer spec for your altitude.

  • Combustion analyzer

    Measures flue gas oxygen, carbon monoxide and temperature to confirm the furnace is burning clean and venting correctly before we leave.

  • Anemometer

    Reads airflow at supply and return registers so we can balance the system and confirm the blower is moving the CFM the unit needs.

  • Duct leakage tester

    Pressurizes the duct system to measure leakage. We use it to find disconnected runs and leaky joints that waste heat in attics and crawlspaces.

  • Multimeter

    Tests voltage, continuity and amp draw on the blower motor, igniter and control board during commissioning and diagnosis.

  • Leak detector

    Electronic and soap-solution testing on every gas connection we make, so a fitting is never left leaking behind a panel.

  • Vacuum pump

    Pulls a deep vacuum on the refrigerant lines when we replace the AC coil alongside a new furnace, protecting the compressor from moisture.

  • ACCA Manual J load calculation

    The industry-standard method for sizing heating and cooling equipment. We measure every room, window, door and insulation value, then calculate the exact BTU load. This is why our furnaces do not short cycle and do not leave rooms cold.

When Littleton Homeowners Replace a Furnace

  • A 20-year-old furnace in a Columbine ranch home fails the week before Christmas.

    We prioritize no-heat calls during cold snaps. We diagnose the failure, confirm the unit is beyond economical repair, and quote a replacement the same day. Most emergency replacements are installed within 48 hours, including weekends. Heat back on before the holiday, with a new 96% AFUE furnace and a 10-year parts warranty.

  • A homeowner in Ken Caryl is planning to sell in the spring and the furnace is 18 years old.

    We install a mid-efficiency furnace with a clean permit record and provide the inspection paperwork for the seller's disclosure. Buyers and their inspectors see a documented, code-correct install instead of a question mark. A clean inspection, a faster sale, and no last-minute price negotiation over the furnace.

  • A TrailMark family wants to replace the furnace and AC at the same time to save on labor.

    We quote a matched furnace and AC system with an AHRI-certified combination, so the efficiency rating on the box is the efficiency you actually get. One crew, one permit, one install day for both systems. A matched system that hits its rated SEER2 and AFUE numbers, with one warranty file instead of two.

  • A Downtown Littleton homeowner with a finished basement wants to add a furnace without tearing up the ceiling.

    We route the flue and ductwork through existing chases and use flex duct where it makes sense, keeping the finished ceiling intact. If ductwork is not feasible, we quote a ductless mini-split as an alternative. A warm basement without a drywall repair bill, and a system that fits the home instead of the other way around.

How Furnace Installation Works in Littleton

Littleton sits at roughly 5,400 feet, and that altitude changes how a furnace runs. Gas appliances need to be derated, or they burn rich, soot up the heat exchanger and produce carbon monoxide. We adjust every install to the manufacturer's altitude chart, which a lot of out-of-town crews skip. Our winters swing hard, with 60-degree afternoons in November and single-digit nights in January, so we size for the cold snap, not the average. Older homes in Downtown Littleton and Columbine often have undersized returns and original 1950s ductwork, and we fix that during the install instead of leaving it for the next guy. If you are comparing furnace replacement near Highlands Ranch CO, ask whether the quote includes a Manual J and altitude derating. Ours does, and it is why our installs pass Arapahoe County inspection the first time.

  • Downtown LittletonOlder homes with original ductwork and small mechanical closets. We often need to re-route flues and add return air to make a modern furnace fit and breathe.
  • Ken CarylTwo-story homes with west-facing glass that gain a lot of heat in the afternoon. We size the furnace for the cold mornings and let the AC handle the afternoon load.
  • TrailMarkNewer construction with tighter envelopes. These homes often need a smaller furnace than the original builder installed, which fixes short cycling and uneven rooms.
  • Roxborough ParkLarger homes on bigger lots with longer duct runs. Static pressure matters here, and we often add a return or upsize a trunk line during the install.
  • High altitude around 5,400 feetFurnaces must be derated for altitude to burn clean. We adjust the gas valve and orifice per the manufacturer chart, which keeps CO levels low and protects the heat exchanger warranty.
  • Hard freeze events in January and FebruaryCondensate lines on high-efficiency furnaces can freeze if they are routed wrong. We slope and insulate the line, and we route it indoors where possible so it does not ice up on a 5-degree night.

From problem to finished result.

  • Ken Caryl ranch: 22-year-old furnace to 96% AFUE

    Before

    A 100,000 BTU furnace from 2002 was short cycling every 8 minutes, the upstairs bedrooms never got above 64 degrees, and the January gas bill hit $310. The heat exchanger had visible cracks and the flue was backdrafting on cold mornings.

    After

    We installed a properly sized 70,000 BTU Carrier 96% AFUE furnace with a new flue and condensate line. Temperature rise is now within spec, the upstairs holds 70 degrees, and the January gas bill dropped to $195.

    Change the 4-inch filter every 90 days, book a fall tune-up, and keep the condensate line clear. The 10-year parts warranty stays valid with yearly maintenance.

  • Downtown Littleton bungalow: cold back bedroom fixed

    Before

    A 1948 bungalow with original ductwork had a disconnected flex run dumping heat into the crawlspace. The back bedroom stayed at 58 degrees all winter while the front room hit 74. The homeowner was running a space heater to compensate.

    After

    We reconnected and sealed the duct run, added a return air path, and installed a new 60,000 BTU Rheem furnace. Static pressure dropped from 0.9 to 0.5 inches of water column, and the back bedroom now holds 69 degrees.

    Keep the crawlspace access clear for yearly duct inspection, and replace the filter monthly during heating season since the home has pets.

  • TrailMark two-story: furnace and AC replaced together

    Before

    A 2008 builder-grade furnace and AC were both failing. The AC was low on R-410A, the furnace igniter had failed twice in two seasons, and the homeowner was facing two separate repair bills within a year.

    After

    We installed a matched Lennox furnace and AC system with an AHRI-certified combination. The new system hits 96% AFUE and 16 SEER2, and the homeowner qualified for 0% financing for 12 months. One permit, one install day, one warranty file.

    Book spring AC and fall furnace tune-ups, change the filter every 90 days, and keep the outdoor condenser clear of leaves and snow.

Furnace Problems We Solve Across Littleton

Most of the calls we get are not surprises. They are the same handful of failures showing up in Littleton homes every winter, and every one of them has a fix.

  • Furnace not heating or blowing cold air

    Furnace not heating or blowing cold air

    We diagnose the ignition sequence, test the gas valve, and inspect the heat exchanger with a combustion analyzer and visual scope. If the exchanger is cracked, we quote a replacement. If it is a $180 igniter, we replace it and you are warm the same day. A furnace that runs but does not heat usually means a failed igniter, a bad gas valve or a cracked heat exchanger. Ignoring it wastes gas and can push carbon monoxide into the house.

  • Short cycling and uneven room temperatures

    Short cycling and uneven room temperatures

    Short cycling is usually an oversized furnace or a duct problem. We measure static pressure and duct leakage, then either correct the ductwork or replace the furnace with a properly sized unit. Most homes see even temperatures within a week. A furnace that kicks on and off every few minutes wears out the blower motor and the heat exchanger faster, and it never gets the far bedrooms warm. Gas bills climb while comfort drops.

  • Rising gas bills with no change in usage

    Rising gas bills with no change in usage

    We compare your current furnace rating to a high-efficiency replacement and show you the payback math. Most Littleton homeowners see $60 to $120 a month in savings during heating season after upgrading to a 96% AFUE unit. An aging furnace loses efficiency every year. A 70% AFUE unit from the 1990s burns roughly 30% more gas than a modern 96% furnace to deliver the same heat.

  • Carbon monoxide detector going off

    Carbon monoxide detector going off

    We treat CO calls as priority. We test the flue with a combustion analyzer, inspect the heat exchanger, and check the chimney and combustion air. If the furnace is the source, we shut it down and quote a replacement the same day. A CO alarm is not a false alarm to ignore. It usually means a cracked heat exchanger, a blocked flue or a backdrafting water heater sharing the same chimney.

A furnace sized right, installed right, and tested before we leave.

  • Lower winter gas bills

    A modern 96% AFUE furnace replaces a 30-year-old 70% unit and cuts gas use by roughly a third. On a typical Littleton bill that is $60 to $120 saved every month from November through March, which pays back a chunk of the install in the first few winters.

  • Heat that reaches every room

    Short cycling and cold bedrooms usually mean the furnace is oversized or the ductwork is leaking. We measure static pressure and check duct leakage before we set the new unit, so the upstairs bedroom actually warms up instead of the hallway thermostat lying to you.

  • No more 2 a.m. no-heat calls

    A cracked heat exchanger or a failed igniter does not fix itself. Replacing a furnace before it fails means you are not calling an emergency line at midnight in January with a house full of kids and a thermostat reading 54 degrees.

  • Warranty and code coverage

    A permitted install with a Colorado HVAC contractor license keeps your manufacturer warranty valid and your homeowner insurance happy. Unpermitted swaps done by a handyman can void both, and we have seen Arapahoe County inspectors flag exactly that on resale.

What you receive

Clear records you can keep and share.

Load calculation

Room-by-room Manual J sizing on paper

Commissioning report

Combustion and temperature rise readings

What to know before you replace a furnace

The two numbers that matter most are the AFUE rating and the BTU size. Get those wrong and you either overspend on gas or freeze in the back bedroom.

  • AFUE rating

    AFUE is the annual fuel utilization efficiency. An 80% furnace wastes 20 cents of every gas dollar. A 96% furnace wastes 4 cents. The gap shows up on your winter bill.

  • BTU sizing

    Bigger is not better. An oversized furnace short cycles, wears out faster and leaves rooms cold. Size comes from a Manual J calculation, not square footage.

  • Altitude derating

    Littleton sits around 5,400 feet. Gas furnaces must be derated for altitude or they burn rich and produce carbon monoxide. We adjust every install to the manufacturer chart.

Local service area

Heating and cooling coverage around Littleton

Outside these areas? Call and ask, we may still cover you. 1234567890

Furnace Installation Questions Littleton Homeowners Ask

Still wondering? 1234567890

Local service team

Get Your Furnace Installation Littleton CO Quote Today

One call, one visit, one written number. We size your furnace with a real load calculation, pull the permit, and install it code-correct so it passes inspection the first time. Call us now and we will get an estimator to your door this week.

Contact Littleton Heating & Cooling

Call us at 1234567890 or email info@littletonheating&cooling.com to book a service call. We answer phones Monday through Friday, 8 a.m. to 6 p.m., and run emergency dispatch seven days a week. Most calls get a same-day window if you reach us before noon.

Thanks. Your request is in and the team will follow up shortly.