AC Installation Littleton CO: Cool, Quiet, Code-Correct

When your old condenser finally quits, AC Installation Littleton CO done right means a system sized to your square footage, ductwork, and sun exposure, not whatever the truck has on hand. We replace aging units across Arapahoe County with Carrier, Trane, and Mitsubishi Electric equipment, pull the permit, and haul the old unit away. Most homes are cooling again the same day.

AC Installation & Replacement
  • Aging condensers
  • R-22 systems
  • Undersized ducts
  • Readings on every visitYou see the numbers before we leave
  • Written scope firstFlat price before any work starts
  • Parts on the truckMost repairs finish in one visit
  • Old equipment hauled awayWe leave the space clean

What Is Included in a New AC Install

Every AC Installation Littleton CO project we do includes the core work below. If your job needs duct modifications, a new line set through finished walls, or electrical upgrades, we quote those separately and in writing before we start.

  • Manual J Load CalculationWe measure every room, check insulation, windows, and orientation, then calculate the exact tonnage your home needs. This is the step most contractors skip, and it is the reason systems get oversized and short cycle.
  • Permit and InspectionWe pull the Arapahoe County mechanical permit and meet the inspector on site. You get a signed-off permit, which matters when you sell the house or file an insurance claim.
  • New Line Set and PadWe run new copper line sets sized to the equipment, braze with nitrogen flowing, and set the condenser on a level composite pad. The old unit, pad, and refrigerant are hauled away and disposed of properly.
  • Refrigerant Charge by WeightWe pull a deep vacuum to 500 microns, then weigh in the exact refrigerant charge per the manufacturer data plate. No guessing by gauge, no overcharge that kills efficiency and compressor life.
  • Thermostat and StartupWe install and configure your thermostat, verify temperature split and static pressure, and register your equipment warranty. Then we walk you through filter changes and settings before we leave.
AC Installation & Replacement

AC replacement for homes

We replace aging condensers, coils, and line sets for homeowners across Littleton. Every install starts with a room-by-room load calculation and ends with a walkthrough of your new thermostat.

  • Ranch and two-story homes
  • Attic and basement air handlers
  • Furnace and AC matched pairs
  • Additions and finished basements

AC replacement for businesses

We replace rooftop and split systems for small commercial properties on a schedule that keeps your doors open. Work is phased so you are never without cooling during business hours.

  • RetailEarly-morning installs before opening
  • OfficesZoned replacement, one floor at a time
  • RestaurantsRooftop units swapped in a single day
  • Property managersMulti-unit scheduling and documentation

What AC Installation Littleton CO Really Involves

AC Installation & Replacement is the removal of an old condenser and evaporator coil and the fitting of a new, correctly sized cooling system, including line sets, electrical, condensate drainage, and thermostat. It is not a swap-and-go job. We start with an ACCA Manual J load calculation, then match equipment and airflow with Manual D duct design so the new unit moves the right CFM through every room instead of short cycling.

Littleton homes face 95-degree July afternoons and single-digit January nights, so your cooling system works a short, brutal season. We see 20-year-old builders-grade units in Ken Caryl and Columbine that still run, but at R-22 pressures and 10 SEER efficiency. Upgrading to a modern R-410A or R-32 system often cuts summer cooling costs by 30 to 40 percent, and pairing it with a furnace replacement keeps the whole mechanical closet matched.

We size the system to the house, then install it like we are the ones paying the July bill.

How Our AC Replacement Process Works

From the first phone call to the final thermostat setting, here is exactly what happens when we install a new cooling system in your Littleton home.

  1. In-Home Assessment

    In-Home Assessment

    We measure every room, check window orientation, insulation, and existing duct sizes, then run an ACCA Manual J load calculation. You get a written proposal with two or three equipment options at different efficiency tiers. This visit takes 60 to 90 minutes.

  2. Equipment Selection

    Equipment Selection

    You pick the system that fits your budget and goals, whether that is a basic 14.3 SEER2 Goodman or a 20 SEER2 Mitsubishi Electric inverter. We confirm the air handler, coil, line set size, and thermostat match, then schedule the install, usually within three to five days.

  3. Permits and Prep

    Permits and Prep

    We pull the Arapahoe County mechanical permit and schedule the inspection. The morning of install, our crew lays drop cloths, protects flooring, and disconnects the old equipment. Most residential changeouts are a one-day job, start to finish.

  4. Installation Day

    Installation Day

    We recover refrigerant with an EPA-compliant recovery machine, remove the old condenser and coil, run new copper line sets, and braze with nitrogen flowing. The new pad is leveled, the disconnect and whip are replaced, and the PVC condensate line is routed to a safe drain point.

  5. Commissioning and Walkthrough

    Commissioning and Walkthrough

    We pull a deep vacuum with a manifold gauge set, weigh in the exact refrigerant charge, and verify static pressure and temperature split. Then we walk you through the thermostat, filter schedule, and warranty registration before we leave.

Tools and Methods We Use

  • Manifold gauge set

    Used to read suction and liquid line pressures during charging and to confirm the system is operating within manufacturer spec after install.

  • Vacuum pump and micron gauge

    Pulls the system down to 500 microns before charging, which removes moisture and non-condensables that would otherwise shorten compressor life.

  • Refrigerant recovery machine

    Recovers R-22, R-410A, or R-32 from the old system per EPA Section 608 rules before we remove the condenser and coil.

  • Anemometer

    Measures airflow at each supply register so we can verify the duct system is delivering the CFM the new equipment needs room by room.

  • Duct leakage tester

    Quantifies how much conditioned air is escaping through joints and boots, which tells us whether duct sealing should be part of the project.

  • Multimeter and combustion analyzer

    Checks electrical draw on the compressor and blower, and verifies furnace combustion safety when we replace a matched AC and furnace pair.

  • Tube cutter and flaring tool

    Cuts and flares copper line sets to exact length with clean, leak-free connections instead of reusing old, work-hardened tubing.

  • ACCA Manual J load calculation

    We measure square footage, insulation values, window area, and orientation, then calculate the exact heating and cooling load for your home. This determines tonnage, not a rule of thumb based on square footage alone.

When to Replace Your Air Conditioner

  • Your AC is 15 years or older and has needed two repairs in the last three summers.

    We quote a full replacement with a Manual J load calculation, walk you through 14.3 SEER2 up to 20 SEER2 options, and schedule the install within the week. We pull the permit and haul the old unit away. You get a system with a 5 to 10 year parts warranty and 30 to 40 percent lower cooling costs, instead of another $900 repair on equipment that is already past its design life.

  • You are selling your Littleton home and the buyer's inspector flagged the aging AC.

    We provide a written replacement quote fast, install a code-correct system, and coordinate the Arapahoe County inspection so the signed-off permit is ready before closing. We work directly with your realtor if needed. The deal closes on schedule with a new, permitted system, and you avoid a last-minute price reduction or repair credit.

  • You are finishing a basement or adding a room and the existing system cannot keep up.

    We evaluate whether a larger central system, a ductless mini-split, or a zoned setup makes the most sense. For most additions, a Mitsubishi Electric mini-split delivers the best comfort without touching your existing ductwork. The new space stays comfortable year-round, and your main system is not overloaded trying to condition square footage it was never sized for.

  • Your AC and furnace are both original to the house and both showing their age.

    We quote AC and furnace replacement Littleton CO as a matched pair, which protects your equipment warranty and often qualifies for utility rebates. One crew, one permit, one install day. Both systems are matched and efficient, your mechanical closet is clean and code-correct, and you avoid paying for two separate installs six months apart.

How AC Installation Works in Littleton

Littleton sits at 5,400 feet, and high altitude changes how AC systems perform. Air is thinner, so equipment loses roughly 4 percent of its rated capacity per 1,000 feet of elevation. We account for that in the Manual J calculation and equipment selection, which is why a system sized for a sea-level home would leave your Littleton house warm in July. Most homes here were built between 1955 and 2005, with a mix of ranch, split-level, and two-story layouts. Older homes in Downtown Littleton and Columbine often have undersized returns and attic air handlers that need extra insulation and condensate protection. Newer builds in TrailMark and Roxborough Park tend to have tighter envelopes, which means correct sizing matters even more. We pull Arapahoe County mechanical permits on every replacement and meet the inspector on site. If you are comparing AC replacement cost Littleton CO quotes, ask whether the contractor runs a Manual J and pulls a permit. If the answer is no, the price is not comparable.

  • Downtown LittletonMany 1950s and 1960s ranches with original ductwork and attic air handlers. We often correct undersized returns and add condensate overflow protection during replacement.
  • Ken CarylMix of 1980s and 1990s two-story homes with builders-grade equipment now reaching end of life. Standard one-day changeouts with matched furnace and coil are common here.
  • TrailMarkNewer, tighter construction with HOA rules on condenser placement. We work with the screening requirements and often recommend variable-speed systems for quieter operation.
  • Roxborough ParkLarger homes on foothills lots with longer duct runs and more sun exposure. Manual D duct checks matter here, and zoned systems are a frequent upgrade.
  • Columbine ValleyEstablished neighborhood with a mix of ranch and two-story homes. Many have finished basements, so we route line sets and condensate drains carefully through finished space.
  • High altitude reduces equipment capacityAt 5,400 feet, AC systems lose about 4 percent of rated capacity per 1,000 feet. We size equipment with that derate factored in, so your system actually hits the thermostat setpoint on a 98-degree day.

From problem to finished result.

  • Ken Caryl Ranch: 19-Year-Old Carrier Replaced

    Before

    A 2007 Carrier 10 SEER R-22 system ran constantly in July, could not hold 76 degrees upstairs, and had been recharged twice in two summers. The homeowner was quoted $1,400 for a compressor replacement on equipment that was already past its design life.

    After

    We installed a Trane 16 SEER2 two-stage system with a new matched coil, line set, and Honeywell thermostat. Upstairs now holds 72 degrees on a 98-degree afternoon, and the July electric bill dropped from $210 to $138.

    Change the 16x25x1 filter every 60 days, schedule a spring tune-up to check refrigerant charge and clean the condenser coil, and keep two feet of clearance around the outdoor unit.

  • Downtown Littleton: Undersized Return Fixed

    Before

    A 1962 ranch had a 3-ton system that short cycled every 8 minutes and left the back bedrooms 6 degrees warmer than the front. Static pressure measured 0.9 inches of water column, nearly double the recommended maximum for the equipment.

    After

    We enlarged the return from 14x20 to 20x25, sealed duct joints, and installed a correctly sized 2.5-ton variable-speed system. Static pressure dropped to 0.5 inches, room-to-room temperature variance fell to 2 degrees, and short cycling stopped.

    Check the return grille for blockage monthly, keep the filter clean, and have the duct system re-tested every three years to confirm static pressure stays in range.

  • TrailMark: Matched AC and Furnace Upgrade

    Before

    A 2004 builder-grade Goodman AC and furnace were both original. The AC used R-22, the furnace had a cracked heat exchanger flagged by a home inspector, and the homeowner was facing two separate replacement quotes totaling over $14,000.

    After

    We installed a matched Lennox 17 SEER2 AC and 96 percent AFUE furnace as a single project. One permit, one install day, and the homeowner qualified for a $600 utility rebate. Total project came in under $12,000 with financing at 0 percent for 12 months.

    Schedule spring AC and fall furnace tune-ups, replace the filter every 60 days, and keep the condensate drain line clear with a yearly flush.

Cooling Problems We Solve Every Summer

Most AC replacement calls start with one of these symptoms. If any of them sound familiar, a new system is usually the smarter spend than another repair.

  • AC runs all day but house stays warm

    AC runs all day but house stays warm

    We test compressor amp draw, refrigerant charge, and duct static pressure to confirm the diagnosis. If replacement is the right call, we size a new system with Manual J and have you cooling again in days, not weeks. Your compressor is likely failing or the system is undersized. You pay full electric bills for half the comfort, and the problem gets worse every summer until the unit quits entirely.

  • R-22 refrigerant leaks that keep coming back

    R-22 refrigerant leaks that keep coming back

    We stop chasing R-22 leaks on 15-year-old equipment. Instead, we install a new R-410A or R-32 system with a fresh line set and a 5 to 10 year parts warranty, so you stop paying for refrigerant you cannot keep. R-22 is phased out and now costs $100 or more per pound. A slow leak means $400 to $800 in recharge costs every summer, with no end in sight.

  • Frozen evaporator coil every few weeks

    Frozen evaporator coil every few weeks

    We diagnose the root cause, whether it is a dirty filter, blower motor failure, or refrigerant leak. If the coil or compressor is compromised, we quote a full replacement and handle the install, permit, and haul-away. A frozen coil means restricted airflow or low refrigerant. Left alone, it strains the compressor and can kill the system entirely, turning a $400 repair into a $7,000 replacement.

  • Short cycling and uneven room temperatures

    Short cycling and uneven room temperatures

    We run a Manual J load calculation, check duct sizing with an anemometer, and install a correctly sized variable-speed system. Rooms balance out, humidity drops, and the equipment stops cycling every 10 minutes. An oversized system cools fast, shuts off, and leaves humidity and hot spots behind. It also wears out faster, with more compressor starts per hour than it was built for.

A correctly sized, permitted system that cools the whole house and costs less to run.

  • Lower Summer Bills

    A 16 SEER2 system replacing a 10 SEER unit typically cuts cooling costs by 30 to 40 percent. On a 2,000-square-foot Littleton home running $180 a month in July, that is real money back in your pocket every season.

  • Quieter Operation

    Modern variable-speed condensers run at 58 to 62 decibels, roughly the sound of a normal conversation. If your current unit rattles the bedroom wall at 2 a.m., new AC installation Littleton with an inverter-driven compressor will change how you sleep.

  • Correct Sizing, Real Comfort

    Oversized units cool fast and leave humidity behind, then short cycle and wear out early. We size every system with a Manual J load calculation so upstairs bedrooms in TrailMark and Roxborough Park actually reach the thermostat setpoint.

  • Fewer Breakdowns Ahead

    New equipment comes with a 5 to 10 year parts warranty and a clean service history. No more $600 mid-July capacitor calls, no refrigerant leak hunts on a system that has already given you 18 summers.

What you receive

Clear records you can keep and share.

Written scope

Model numbers, tonnage, and itemized pricing

Permit record

Arapahoe County mechanical permit and signed inspection

Startup report

Vacuum, charge, static pressure, and temperature split

Sizing and efficiency, explained plainly

Two systems with the same tonnage can perform very differently depending on how they are matched and installed. Here is what actually drives comfort and cost in a Littleton home.

  • Tonnage is not a guess

    Tonnage comes from a Manual J load calculation that measures your home's windows, insulation, and orientation. A rule-of-thumb guess often oversizes the system, which causes short cycling and higher humidity.

  • SEER2 is the real rating

    SEER2 is the current efficiency standard and reflects real-world duct and airflow conditions. A 16 SEER2 system typically cuts cooling costs 30 to 40 percent versus an older 10 SEER unit.

Local service area

Heating and cooling coverage around Littleton

Outside these areas? Call and ask, we may still cover you. 1234567890

Frequently Asked Questions

Still wondering? 1234567890

Local service team

Get Your AC Installation Littleton CO Quote Today

Same-day estimates, written pricing, and financing options from 0 percent for 12 months. Call us and we will size your system right the first time. Our technicians are NATE-certified and every install is permitted and inspected.

Contact Littleton Heating & Cooling

Call us at 1234567890 or email info@littletonheating&cooling.com to book a service call. We answer phones Monday through Friday, 8 a.m. to 6 p.m., and run emergency dispatch seven days a week. Most calls get a same-day window if you reach us before noon.

Thanks. Your request is in and the team will follow up shortly.